Loading
Hi. I could not install the editor by downloading from the official page, from git and from pypi. It gives me an error. Firstly I have...
Started by eabdala in OpenPLC Editor
Hi, I am a new man for the PLC, I had setup this openplc software, but I donot know how to connect with the linux system? how to share the memary ?...
Started by sunbo in OpenPLC Editor
Where I will get source code for this project?
Started by mkharsha in OpenPLC - General Discussion
Hello first want to tell that I think OpenPLC is a great tool to learn about "OT" Hardware and communications and very easy to set up, so...
Started by arraiz in OpenPLC - General Discussion
Good morning all ! I write this message in order to know if it is possible to recover or extract the code in C generated by openPLC? I am worth...
Started by kooroshtux in OpenPLC Projects
Hi I would like to include information about the tcp/ip sockets on my UI Status Page. The sort of information I'm looking for is implemented in...
Started by NWT.Stuff in OpenPLC - General Discussion
Hi I would like to consider using DNP3 instead of Modbus for a communications protocol with OpenPLC. I am reasonably familiar with Modbus commands...
I loaded first demo project into Runtime. I tried to setup PB1 or PB2 value to true but it was kept same "false" value even I chose...
Started by xudesheng in OpenPLC on PC
Hi all, Myself and a couple others been working on a major update to OpenPLC which you can read about at ...
Started by garretfick in News & Announcements
Hi, I'm trying to configure one Modbus slave and I'm getting the message " Please fill out all the fields before saving", my slave only...
Started by Rox in OpenPLC on Raspberry Pi
I recently installed Open PLC Runtime using the script ./install.sh rpi I just read that there are new features added to the repository, and I...
Started by velle in OpenPLC on Raspberry Pi
I have been trying to use the initial value in OpenPLC editor using ladder logic, but when I try to put a value in the initial value column, it fails...
Started by electron1 in OpenPLC Editor
OK sure this TOPIC could be a debatable and interesting one. Just interested in everyone's thoughts themselves. OK SCADA. what does it mean ? Is...
Hi I'm working on a conversion project from Python to OpenPLC. All Graphics and Animation has already been done for the old Architecture. This is...
I've located properly working C code to read the humidity and temp values from the AM2302, but my C coding skills has about 25 years of rust on it...
Started by bkintz in OpenPLC on Raspberry Pi
I've being using OpenPLC in my classes (I'm a professor) and it's wonderful! Congrats! During my studies of the platform I've tried to use it with...
Started by andrade.juba in OpenPLC on PC
Hi, I tried to set up a PID block but I think I was unable to declare the variables properly. I'm attaching the screenshot. Could someone please...
Started by rodrigo_rolle in OpenPLC Editor
Is there a way to avoid the dependency of openPLC on WiringPi ? I would like to map my IO using a Python routine on RPI start up and addressing GPIO...
Started by NWT.Stuff in OpenPLC on Raspberry Pi
Hi, I am setting up a sample project in OpenPLC + FactoryIO. In particular, among other things I need to update a counter every time a piece...
Started by adriano.mele in OpenPLC - General Discussion
Hi, we develop the RevolutionPi which is an industrial RaspberryPi based on the Compute Module (CM). A community member has asked how he could...
Started by dirk in OpenPLC Hardware
Hi, I'm new using this editor and I have some issue when I try to launch it, something about wx lib (python). What version the python do I need, 2.7...
Started by gtomasini in OpenPLC Editor
I am struggling to compile this Code. I am writing successfully to my Modbus Control Word (MW0). The Code works perfectly without Rung 2. My...
Started by NWT.Stuff in OpenPLC Editor
Hello! I am quite new in ladder logic - trying to learn something about. However, now I got stuck on implementating of rotary encoder (something...
Started by m_ledo in OpenPLC Editor
Hi thiagoralves , I am following Heat Exchanger PID example as given in ...
Started by rmshahid in OpenPLC Projects
I am new to openPLC. I was just wondering if it is possible to configure the internal pullup and pulldown resistors on RPI inputs in the editor or...
Supported videos include:
Please paste your code into the box below:
